| Height |
23 inches |
| Depth |
23 inches |
| Width |
17 inches |
| Weight |
|
 Free-Standing |
45 LBS |
| Fully Enclosed |
100 LBS |
| Case Material |
Military Grade Plastic |
| All other Materials |
Aluminum, brass and plastic |
| Operating Temperature Range |
35 to 110 degrees, F |
Gas Supply Sources
02 Main and Cylinders
Air and/or Air Compressor
Oxygen Concentrator |
38-70 psi (50 psi is optimal)
38-70 psi (50 psi is optimal)
3-10 psi |
| Flowmeter Fresh Gas Flow |
1 to above 20 lpm (each flowmeter) |
| Oxygen Flush Valve |
Recessed, self-closing, push button color coded and labeled, provides 45-55 lpm contant. flow while push-button is depressed |
| CO2 Absorber System |
King Systems KAB-9, (re-fillable) or KAB-1 (pre-filled/disposable)
|
| C02 Absorber Canister Capacity |
400 grams soda-lime |
| Directional Valves |
Built-in the CO2 absorber |
| CO2 Absorber Holding Bracket |
Plastic, secured with knob to main frame of machine. |
| Bag-Ventilator Switch/PRV and Scavenger Outlet Port |
Hand-operated selector switch and rotating knob for PRV and scavenging outlet. |
| Bellows |
Latex free, upward inflating, range from
0 to 1.6L |
| Bellows Pressure Relief |
Pre-set at 60 cmH20 |
| Common Gas Outlet |
Size indexed, quick connect |
| Tubing Circuit |
King Systems F-360-61 or any standard anesthesia circle circuit |
| Gas Pressure Hoses |
DISS/thread indexed, female connectors at both ends |
| Gas Inlet Manifold |
DISS/thread indexed, male connectors with one-way valves |
| Oxygen and Air Supply Gauges |
0-3000 PSI reading color coded and
clearly labeled |
| Gas Inlet Manifold Filters |
Located behind Manifold Air and O2 inlet male connectors. |
Gas Inlet Pressure Regulators
Main Supply Cylinder
Safety back up Cylinder |
0-3000 PSI reading color coded and clearly labeled
DISS/thread indexed for O2
Pin indexed, yoke mounted for "D" and "E" cylinders for 02 |
| Oxygen Supply Alarms |
|
| Main and Safety back-up |
Pneumatically actuated when O2 supply falls below 35 psi |
O2 Concentrator
|
Pneumatically actuated when O2 supply falls below 1psi |
| Alarm power source |
9-volt battery located in body of alarm box |
| Alarm on/off |
Labeled toggle switch located on body of alarm box. |
| Air and O2 Flowmeters |
Calibrated and scaled 0-10 LPM color coded. O2 flowmeter has a fluted control knob for easy identification by touch |
| Oxygen Concentrator |
To power O2 flowmeter only |
| Air Compressor |
May be used to power ventilator and air flowmeter |
| Oxygen Analyzer/Monitor |
OM-25-ME (or equivalent) Sensor life expectancy 2 years under normal conditions |
| Oxygen Analyzer Power Source |
2 each AA batteries, life expectancy approx. 3000 use hours |
| Auxillary O2 Flow Selector |
Scaled 0-10 LPM in set increments, used for pre/post anesthesia |
| Vaporizer |
Penlon SigmaDelta Series, bolt (cage) mounted, temperature compensated, very low maintenance |
| Airway Pressure Gauge |
Dual scaled in cmH20 and mmHg, located on front panel of ventilator |
| Pressure Gauge Tubing |
Attached to bag/vent switch arm |
| Mechanical Ventilator |
Pneumatically powered, time cycled, volume constant, pressure variable |
| Volume Range |
0 to 1.6 L |
| Insp. Flow Range |
0 to .90 lps |
| Insp. Time Range |
0.2 to 3.0 seconds |
| Exp. Time Range |
0.2 to 30 seconds |
| Ventilator Gas Power Requirements |
40 to 70 psi, 50 psi optimal
Use toggle switch to select gas source |
| Waste Gas Scavenger |
Positive and negative relief valves, 1 L reservoir bag, vacuum control knob |
| Total Machine Gas Leakage |
@ 30cm H2O
@ 80cm H2O |
0ML/min
0ML/min |
| Internal System Compliance |
@ 20cm H2O
@ 40cm H2O |
1.1ML/cm H2O
1.3ML/cm H2O |
| Internal System Resistance |
@ 1.0L/sec gas flow
@ 0.5L/sec gas flow |
4.11cm H2O
1.80cm H2O |
| APL Valve Pressure Drop |
@ 3.0L/min gas flow
@ 30L/min gas flow |
0.12cm H2O
1.03cm H2O |
| Storage |
|
| Indoor |
+ 160 °F Allow unit to warm to room temp. |
| Indoor/Outdoor |
-30 °F Allow unit to warm to room temp. |
